Published price brackets and clear material standards govern every service call. Denver property owners face no surprise dispatch add-ons, no speculative flat rates, and no installations without required municipal permits.
“Why is there a spread in your price ranges, and what determines whether my job is at the low or high end of the bracket?”
Every electrical quote is determined by five physical variables: urgency, access difficulty, materials, municipal permits, and wiring age.
Electrical contracting is physical work shaped by existing structure. When we install a Level 2 EV charger in an unfinished garage where the main panel is six feet away on open drywall, the job sits at the $1,480 minimum. When the same charger requires coring through a brick exterior, trenching 40 feet of buried conduit, or fishing through three finished floors of lath and plaster, material costs and labor hours push the project toward $2,504.
The table below outlines our standard hourly rates and service tiers. Estimates are provided in writing on the day of inspection before work begins.
| Service Description | Billing Basis | Typical Price Range | Standard Inclusions |
|---|---|---|---|
| Electrician Service Call | Per visit | $90 – $260 | Site dispatch, voltage and continuity check, circuit identification, visual code assessment. |
| Licensed Electrician Hourly Rate | Per hour | $75 – $155 | Hands-on labor billed in 15-minute increments after the initial service visit minimum. |
| Diagnostic / Minor Repair | Per visit | $166 – $281 | Fault tracing, open neutral remediation, breaker trip isolation, receptacle short repair. |
| Duplex Outlet Installation | Per point | $202 – $342 | Commercial-grade 15A/20A tamper-resistant duplex outlet, steel or plastic box, branch drop. |
| Ceiling Fan Replacement | Per point | $269 – $455 | Removal of old fixture, UL-listed fan-rated box installation, balanced assembly, speed switch. |
| 200 A Service Panel Modernisation | Per project | $2,512 – $4,250 | 200A main breaker panel, copper busbars, dual ground rods, Denver permit & utility disconnect. |
| Level 2 EV Charger Feed | Per project | $1,480 – $2,504 | Dedicated 50A/60A 240V circuit, 6 AWG copper wire, EMT surface conduit, disconnect switch. |
| Generator Transfer Switch | Per project | $1,211 – $2,049 | Manual mechanical interlock or transfer panel, exterior power inlet box, critical load branch wiring. |
Every line is specified with commercial-grade conductors, enclosures, and breakers. We quote what the job actually takes to pass city inspection on the first visit.
Our standard dispatch puts a licensed electrician with a fully equipped trade van at your residential or commercial location in Denver. Includes preliminary circuit tracing, supply voltage verification, main panel safety check, and an itemized written estimate for required repairs.
Applied for custom installations, commercial tenant improvements, code compliance corrections, and troubleshooting beyond initial diagnostic visit minimums. All hands-on work is executed by licensed electricians and billed accurately in 15-minute increments.
Specialized troubleshooting of mystery breaker trips, nuisance AFCI/GFCI shutoffs, burning smells, flickering lighting banks, and dropped neutral connections. Includes instrumented resistance and voltage testing, thermal checking of breaker stabs, and minor on-the-spot component repair.
Installation or retrofit of 15A and 20A commercial-grade duplex outlets. We install UL-listed tamper-resistant receptacles, ground fault circuit interrupters (GFCI) in wet locations, and steel plaster rings or retro-boxes inside existing walls without damaging surrounding drywall.
Safe replacement of standard ceiling light fixtures or damaged fans with heavy-duty ceiling fan assemblies. Standard plastic lighting boxes cannot support dynamic rotational load; we install UL-listed steel fan-rated spreader boxes anchored between structural joists to guarantee physical stability.
Complete modernisation of obsolete 60A/100A split-bus, fuse, or hazardous Zinsco/Federal Pacific panels. We supply and install a 200 A Siemens or Square D QO copper-bus load center, Type 2 whole-house surge suppression, dual driven 8-foot ground rods, and handle all Xcel Energy utility disconnect scheduling and Denver municipal building permits.
High-amperage dedicated 240-volt charging circuit installation for Tesla, Rivian, Ford, and universal J1772 chargers. We run thick 6 AWG THHN copper wire inside steel EMT conduit, install a dual-pole 60A breaker, wire an emergency disconnect switch where required, and torque all terminations to manufacturer specifications.
Safe manual transfer switches and mechanical interlock plates preventing dangerous electrical backfeeding during grid outages. Includes installing an exterior NEMA 3R weatherproof 30A or 50A power inlet box, heavy-duty interior interlock hardware, and wiring essential home circuits (furnace blower, refrigeration, lighting, sump pump).
Branch feeds from 15A to 60A, EV chargers, and service disconnects utilize pure copper conductors exclusively. Copper provides superior conductivity, lower resistance, and minimal thermal creep, preventing the loose terminal overheating seen in older aluminum branch wiring.
Exposed wiring across Denver basements, brick garages, and exterior service entrances is enclosed inside rigid metallic EMT tubing or heavy-wall Schedule 80 PVC. We never leave unshielded Romex NM-B cable subject to mechanical damage or environmental wear.
Every main panel upgrade features electro-tin plated solid copper busbars rather than prone-to-corrosion aluminum interior bars. These maintain low contact resistance under heavy continuous loads and prevent breaker stab burning.
Written itemized estimates are presented on the day of inspection. Call directly or submit project specifications online for prompt Denver dispatch.